JPS METAL & ALLOYS/ISO 9001:2015 CERTIFIED/MUMBAI, INDIA
VEDAANT@JPSMETAL.IN/+91 22 66630010
IndustriesContact UsBlogAbout

PSQ Shafts (Pump Shaft Quality Bars) Manufacturer & Exporter in India

Pump shaft quality (PSQ) bars in stainless steel, duplex, precipitation-hardening and nickel alloys: turned, ground, polished and straightened for pumps and rotating equipment.

Overview

PSQ (pump shaft quality) bars are round bars that have been turned, ground and polished to a close diameter tolerance and straightened along their full length, ready to be machined into pump shafts, impeller shafts and other rotating parts.

Pump shafts run at high speed under load, so small errors matter. A bar that is not straight vibrates and wears bearings and mechanical seals. A diameter that is out of tolerance stops bearings, sleeves and impellers from fitting correctly. PSQ bars are processed beyond standard bright bar to control straightness, diameter, roundness and surface finish, which reduces machining time and helps the finished shaft run true.

JPS Metal & Alloys manufactures PSQ bars and PSQ shafts in stainless steel (SS 316 / 316L, 410, 420, 431), precipitation-hardening grades (17-4 PH, 15-5 PH), duplex and super duplex, Monel 400 and Monel K-500, and nickel alloys such as Inconel 625 and 718. Bars are supplied with EN 10204 3.1 mill test certificates and full heat traceability, cut to length, or machined into finished pump and valve shafts.

We manufacture PSQ shafts for pump manufacturers, OEMs, maintenance and repair workshops, and valve makers in India and export markets including the GCC, Europe and Southeast Asia.

Types of PSQ Shafts & Bars

TYPE

Turned, Ground & Polished PSQ Bar

Standard PSQ bar: peeled, centreless ground, polished and straightened.
TYPE

High-Strength / Strain-Hardened PSQ

SS 316 and similar grades in strain-hardened condition for higher yield strength.
TYPE

Precipitation-Hardened PSQ

17-4 PH and 15-5 PH in H1025, H1100 or H1150 condition for strength and toughness.
TYPE

Duplex & Super Duplex PSQ

2205, 2507 and S32760 for seawater, brine and chloride service.
TYPE

Nickel Alloy PSQ

Monel K-500, Monel 400, Inconel 625 and 718 for severe corrosion and high strength.
TYPE

Finished Pump Shafts

Machined to drawing with keyways, threads and steps, ready to install.

Key Features & Advantages of PSQ Shafts

  • Turned, centreless ground and polished surface for seal and bearing journals
  • Straightened and checked along the full length to limit vibration
  • Manufactured to a close, typically minus (undersize) diameter tolerance to your pump specification
  • Grades from SS 316 and 410 to 17-4 PH, duplex, Monel K-500 and Inconel
  • EN 10204 3.1 mill test certificate, PMI and ultrasonic testing on request
  • Cut to length or machined into finished shafts in Mumbai

Specification

ParameterDetails
StandardASTM A276 / A479 / A564 (stainless), B164 / B865 (Monel), B446 / B637 (Inconel), B473 (Alloy 20)
Size RangeMetric and inch diameters; send your size and length
ConditionAnnealed, strain-hardened, H1025 / H1100 / H1150 (17-4 PH), age-hardened (Monel K-500, Inconel 718)
Finish & ToleranceTurned, ground and polished; minus (undersize) diameter tolerance to your specification
StraightnessStraightened and checked by total indicator reading (TIR) to your specification
CertificationEN 10204 3.1; PMI, ultrasonic testing and third-party inspection on request
Supplied ByJPS Metal & Alloys, Mumbai

Available Grades & Material Standards

Material FamilyGrades and Standard
Stainless Steel
ASTM A276 / A479
Precipitation Hardening
ASTM A564
Duplex & Super Duplex
ASTM A276 / A479
Nickel Alloys
ASTM B164 / B865 / B446 / B637 / B473 / B574

How We Manufacture PSQ Bars

Our PSQ bars start as hot rolled or forged bar in the required heat-treated condition. The bar is turned (peeled) to remove the surface skin and any decarburisation, straightened, then centreless ground to final diameter and polished. Straightness and diameter are checked along the full length before the bar is packed. Ultrasonic testing can be added to confirm internal soundness before the bar is machined into a shaft.

How to Choose the Right PSQ Grade

Choose the grade by the pumped fluid and the load on the shaft. SS 316 suits water and mild chemicals. SS 410 and 431 give higher strength in fresh water and general service. 17-4 PH offers high strength with good corrosion resistance for most industrial pumps. Duplex and super duplex suit seawater, brine and chloride-bearing fluids, and Monel K-500 combines high strength with excellent seawater resistance. For sour (H2S) service, check the hardness limits in NACE MR0175 / ISO 15156.

With your enquiry, send the grade and condition, diameter and tolerance, length, straightness requirement and quantity. If you have a shaft drawing, we can also quote the finished machined shaft.

Testing & Inspection

Every lot of PSQ bars we manufacture is checked before dispatch. Typical tests and inspections include:

  • Chemical analysis and positive material identification (PMI) against the specified grade
  • Mechanical tests: tensile, yield, elongation and hardness as per the material standard
  • Straightness (TIR) and diameter check along the full length
  • Surface finish and visual inspection of the ground surface
  • Ultrasonic testing for internal defects (on request)
  • Third-party inspection by an agency of your choice (on request)

Typical Applications

Centrifugal pump shaftsVertical turbine pump shaftsSubmersible pump shaftsSeawater & marine pumpsValve stemsAgitator & mixer shafts

Packing, Marking & Delivery

To protect straightness and the ground surface, PSQ bars are packed individually in protective tubes or wooden boxes, with end caps and a tag showing grade, size, condition and heat number. Export consignments are crated with moisture protection and shipped from Nhava Sheva (JNPT), Mumbai.

Each shipment includes the EN 10204 3.1 mill test certificate, packing list, commercial invoice and certificate of origin, with inspection reports on request.

Looking for Round Bars in a specific grade, size or quantity? Send us your requirement and we will respond with pricing and lead time.

Request a Quote →

Frequently Asked Questions

What is a PSQ bar?
PSQ stands for pump shaft quality. A PSQ bar is a round bar that has been turned, ground, polished and straightened to a close diameter tolerance, ready for machining into pump shafts and other rotating parts.
What is the difference between a PSQ bar and a normal ground bar?
Both are ground, but a PSQ bar is also straightened and checked along its full length to a tight straightness limit, usually with a minus (undersize) diameter tolerance, so the finished shaft runs with minimal vibration.
Which grades are used for pump shafts?
Common PSQ grades are SS 316, SS 410, SS 431 and 17-4 PH for general service, duplex and super duplex for seawater and brine, and Monel K-500 or Inconel 625 / 718 for severe corrosion with high strength.
Can you supply finished pump shafts?
Yes. We manufacture PSQ bars cut to length and can machine them into finished pump and valve shafts to your drawing.

Related Guides

Guides to help you specify, order and inspect pump shaft material.

Services, Grades and Export

Need material cut, treated or finished? We offer custom cutting to size, heat treatment, machined components and forged components. See the full list of material grades, our quality and certification process, and export capabilities.

Specification

StandardASTM A276 / A479 / A564 / B865
FinishTurned, ground, polished
StraightnessChecked by TIR
CertificationEN 10204 3.1

Get a quote for Round Bars — grade, size and quantity.

Request a Quote →